Suburbs we cover here: Umbilo, Congella, Bayhead, Berea
Glenwood is old Durban housing on tight stands, a lot of it on a slope, with garages that were built for cars much smaller than the ones parked in them now.
What we see in Glenwood
Low lintels are the standing problem. Plenty of these garages have under 300mm above the opening, which rules out a standard sectional and its tracks. People find this out after they have paid a deposit somewhere else.
A roller shutter solves it because the curtain rolls into a much smaller headbox, and where even that is tight we can build a compact barrel or mount externally. Either way we measure the lintel, the side room and the floor fall before quoting, not after.
Getting on site
Older streets mean narrow driveways and not much room to work, so we survey for access as well as for the opening. If the door has to come in past a boundary wall or down a side passage we would rather know before manufacture than on the day. Where the garage is under the house we also check that the floor and the lintel are what they look like, because on stock this age they often are not.
Motors, backup and load shedding
Older garages usually have no dedicated circuit and often no plug point near the door at all. We include that in the quote rather than leaving you to arrange an electrician afterwards. Backup power matters here too, and we size it to actually cycle the door through a load shedding block rather than fitting a token battery that manages one opening.
Repairs on any make
On doors this age the honest answer is often a repair, not a replacement. A spring set, new pivots and a track realignment will bring a sound door back for a fraction of a new install, and we will do that where the frame is still good. Where the frame has rusted through at floor level, which is common in these older openings, we say so plainly rather than fitting new hardware to something that will not hold it.
What it costs
We quote Glenwood jobs off a free measured survey, itemised so you can see what the door, the motor and the installation each cost, and fixed in writing before anything is manufactured. We do not quote a range over the phone and then adjust it on site, because that is not a price, it is a deposit.
How soon we can be there
Surveys in Glenwood are normally within one working day and quotes follow the same day the survey is done. Manufacture depends on the door, and we give you a real date rather than an optimistic one. Breakdowns are attended same-day wherever we can reach you.
Getting a quote
Send us the opening, or ask for a survey and we will come and measure it. Either way you get an itemised written price for your Glenwood door, valid as quoted, with no charge for the visit.
Roller shutter and industrial door services in Glenwood
Roller Shutter Doors in Glenwood
Every curtain we hang in Glenwood is manufactured to the measured opening rather than cut down from a stock size, in galvanised, perforated, transparent or powder-coated finishes.
Roller Shutter Door Installation in Glenwood
Installation in Glenwood is handled by our own crews, working to your hours where an opening cannot be closed during trading.
Roller Shutter Door Repairs in Glenwood
Most of our Glenwood work is on doors we did not fit: jumped curtains, worn barrel bearings, broken springs, frayed cables and rusted bottom rails.
Roller Door Repairs in Glenwood
A roller door in Glenwood can normally be repaired rather than replaced — individual slats, guides and gear are all replaceable while the rest of the curtain stays.
Industrial Roller Shutter Doors in Glenwood
Heavy-duty curtains for Glenwood warehouses, workshops and loading bays, braced for the span and specified for the cycle count.
Industrial Roller Shutter Door Repairs in Glenwood
When an industrial shutter stops in Glenwood the building stops with it, so we attend same day and repair on the first visit wherever parts allow.
Roller Shutter Door Manufacturers in Glenwood
We are a manufacturer, not a reseller, so a door supplied to Glenwood can be matched, repaired and re-slatted years later from the same works that built it.
Industrial Door Manufacturers in Glenwood
As industrial door manufacturers we build to the Glenwood site rather than to a catalogue, including non-standard spans and heights.
Industrial Door Repairs in Glenwood
Industrial door repairs across Glenwood: straightened guides, replacement slats, new barrel bearings, rebuilt bottom rails and motor replacements.
Roller Shutter Door Servicing in Glenwood
A service contract in Glenwood catches the dry guide and the worn bearing before either becomes the callout that stops your day.
Emergency Roller Shutter Door Repairs in Glenwood
A door stuck open in Glenwood is a security problem and one stuck closed is lost trading, so we run a 24-hour standby for both.
Need a door in Glenwood?
Send the opening size and your suburb. A consultant calls you back, usually within two working hours — or call the standby number if the door has already stopped.
What customers say
Reviews from Glenwood and nearby
Handled professionally from start to finish
Excellent service from start to finish. RDSA installed our new roller shutter door and the whole process was handled professionally. The door looks great and works perfectly.
Verified customervia Google
They clearly knew what they were doing
RDSA fitted roller shutter doors at our commercial property. The team was professional, efficient and clearly knew what they were doing.
Verified customervia Google
Noisy door fixed properly
Highly recommended for garage door repairs. Our door was making a terrible noise and struggling to open. RDSA identified the issue and fixed it properly.
Verified customervia Google
Our work
Doors we have built and fitted
Common questions
Roller doors in Glenwood
A roller shutter, in most cases. Plenty of the older garages in Glenwood have under 300mm above the opening, which a standard sectional and its tracks simply cannot use. A roller curtain rolls into a much smaller headbox, and where even that is tight we can build a compact barrel or mount externally. We measure the lintel, the side room and the floor fall before quoting, so you find this out from us rather than after paying a deposit somewhere else.
It depends on the frame, not the age. If the frame is sound, a spring set, new pivots and a track realignment will bring the door back for a fraction of a new install and we will happily fit that. If the frame has rusted through at floor level, which is common in older Glenwood openings, new hardware will not hold and we will tell you so rather than take the repair money twice.
Not for us, but it needs to be in the quote. Older houses in Glenwood often have no dedicated circuit at the door at all, so we include the electrical work rather than fitting the motor and leaving you to arrange an electrician afterwards. We also size the battery backup to actually cycle the door through a full load shedding block, not just once.
Related
Also worth a look
Roller Shutter Doors Isipingo
Industrial units, retail frontage and coastal exposure
Roller shutter doors, garage doors and industrial shutters manufactured at our own works and installed across Isipingo by our own teams.
Roller Shutter Doors Jacobs
Heavy industrial, manufacturing and 24-hour operations
Roller shutter doors, garage doors and industrial shutters manufactured at our own works and installed across Jacobs by our own teams.
Roller Shutter Doors Kloof
Large stands, long driveways and mist belt damp
Roller shutter doors, garage doors and industrial shutters manufactured at our own works and installed across Kloof by our own teams.